$24.95 $42.95
| /
Outdoor MultiSensor
PRODUCT HIGHLIGHTS
- Security alerts: Get instant motion reports to your Z-Wave hub whenever movement is detected.
- More climate data: Monitor temperature outdoors or indoors and use this information to trigger connected devices in your system.
- Smart lighting: program your Z-Wave outdoor lights to come on when the Zooz sensor reports motion and lux levels below your preferred set point
- Z-Wave Long Range ready:extend the wireless coverage up to1300 feet if your hub supports Long Range
- Power it with 2 CR123A batteries (included) or a 12-24 V AC/DC connection (sold separately)
- Works as Z-Wave signal repeater when powered with 12-24 V AC/DC (do NOT pair the sensor on USB cable and then switch to batteries)
- 800 series Z-Wave chip:more range for reliable wireless communication
- SmartStartandS2 authenticatedsecurity
- Advanced settings to customize your sensor, including the ability to disable reporting for any sensor
- CHECK HUB COMPATIBILITY BEFORE BUYING (NOT SUPPORTED BY WINK OR ALARM PANELS)
- Modern minimaldesign with a multi-directional mini mounting bracket
- Extended 5-year warranty (if registered within 30 days of purchase) andlifetime tech support
NOTE: Z-Wave gateway controller required - sold separately. You need a security enabled controller to take full advantage of the product.
SPECIFICATIONS
- Z-Wave Region: US / CA / MX
- Z-Wave Chip: 800 series
- Power: 2 CR123A battery (included) / 12-24 V AC/DC (sold separately)
- Z-Wave Range:Up to 150 feet line of sight (or up to1300 feet with Long Range enabled)
- Motion Detection: 30 feet
- Operating Humidity:8%- 100% non-condensing
- Light Sensor Detection Range: 0 – 65535 lux
- Operating Temperature: 14°F to 122°F (with accuracy of ±2°C)
- Dimensions: 2.34” x 2.4” x 2.75”
- Installation: Indoor / Outdoor (IP66 rated)
RESOURCES
Zooz 800 Series Z-Wave Long Range Outdoor Motion Sensor ZSE70 800LR Manual (PDF)
WORKS WITH
- Z-Box Hub(recommended for Zooz products)
- Home Assistant(Z-Wave JS)
- HomeSeer (with Z-Wave Plusplug-in)
- Hubitat (with custom driver)
- SmartThings Hub (with custom lua driver)
NOTE: If you don't see your Z-Wave controller on the list above, please contact us before you purchase this product.
GETPOWER SUPPLY
DC:
Your existing landscape lighting low Voltage power source will work great too!
Customer Reviews
Based on 22 reviews
64%
(14)
36%
(8)
0%
(0)
0%
(0)
0%
(0)
A
Ace
Motion Detection works really well! No false detections
Using HA automation to warn me of people in the backyard. It works perfectly, with no false detections as of yet. Easy to install, although removing the back cover counter-clockwise required a great deal of strength. I put some silicon grease when I screwed the cover back on to add more waterproofing and to makie it easier to close in the upright position. Suggest to tighten the little screws holding down the pivot arm to have a firmer mount for the final installation. I installed it under the gutter facing the backyard. Light level detection seems good. Temperature detection seems a little off by a few degrees during a sunny day however. Maybe something that can be fixed in a firmware update?
R
Robert Lefler
Great Service & Great Product
Zooz products are great and The Smartest House has fast shipping. The only place I would order from!
J
John M.
Works well be need some additional settings
This unit works well but I was unable to adjust the range of the detection, just the sensitivity. The unit is installed close to a street and picks up traffic. Being able to shorten the range would be helpful.
K
Ken Wood
Works great
Replaced earlier versions of the zooz outdoor sensor. Easy setup, longer range.
Z
Z-Wave Fan
Plusses, minuses
This sat on my desk for a couple of months while I considered how to mount it - it is designed to be placed facing away from a vertical wall which is problematic for me. I eventually screwed it to a Simpson STC bracket as shown. The unit snaps to the swivel base by pushing it upward, so a plastic spring holds it against gravity. Time will tell how well that works. I'm using battery power so it will be removed and replaced regularly, though I hope to find a way to get 12V to it.
The device paired with S2 security on the second try. The Zooz driver gives easy, intuitive access to all the settings. Temperature and illuminance data appears accurate, and motion is reported instantly.
The manual says the unit "best detects movement to the sides of the lens rather than activity directly in front of it." It does seem to work in my application where it's pointed straight at the area I want to monitor, twenty feet away.
